Home F ACTS, Q UESTIONS &  A NSWERS Introduction (CLICK HERE) For More SPECIAL FEATURES About Us

Question: What size Engine  do you recommend or the least size             in horse power that you build your machines with?

Answer: We recommend using  no less than 18 H.P.  for power              and Torque in allowing maximum response, power &              performance. Some Manufacturers try to pass off their units as powerful commercial truck mounts using 13 &             15 HP engines, but they are only fooling themselves.

Question: Can a Truck Mount that has only (1) Heat Exchanger              produce adequate High Water temperatures for                  commercial carpet cleaning?

Answer: Only if the Heater is designed like the  Blue Barons  use.            This unique Patent Pending Design uses Axis Point                Technology to quickly and efficiently transfer the Exhaust           Heat into the water. Alot of customers tell us that our Primary Heater (with             it's special internal design is all they need for heat.                 We recommend that all Heat Systems have some form            of Pre-Heating Exchanger installed (Especially for the              Winter Season) as  well as a sufficient water storage              capacity which often can be at least 2 to 3 Heaters               depending on the size and length of the internal tubing.      We welcome  you to Demo any of our units and we can            prove to you how HOT these machines get. You won't             be disappointed.

Question: What is the typical water temperature range for most             Truck Mounted Units? Answer:  A  Well-Engineered  Truck Mount Carpet Cleaning System, supplied with cold water, is capable of producing a reliable water temperature of up to 190-240 degrees F which can vary depending on Extraction Style / Methods, Engine Speed, Flow Rate (Size of Wand Jets), Mode of Operation and Design lay-out of Heat Exchanger Tubing / Linear Feet of Tubing. Our New Design Heaters using  Axis Point Technology  TM are so effective, that  its popularity is now sweeping the  country!

Question: Is it important the way a  Truck Mount Carpet Machine FRAME   is structurally built?

Answer: Yes, We take  Pride  in building our frames with 11                gauge steel which surrounds the entire Engine                   and assemblies and not just an  " Engine On A box " with the engine & components are unprotected as well as concealed hidden and hard to reach components.  We make it easy for the Customer to service their own            machine with out paying some so called "Professional             Tech" $75 to $100 an hour to fix. Also, Our Structual              Framing will add  Maximum Protection  for you and your            machine while allowing your components to breath.  SEE BELOW  Contact Us Heat Exchangers Model 33 SE Model 36 SE Model 45 SE Model 47 XL

Heat Exchangers Page Here MORE INFO HERE

***See Comparison of Conpetitions Heater laylout vs. Blue Baron's  toward bottom of  this page***.

< < V

V V V V

V

V V V V

Smother Cover V Front Rear

Rear

V TYPICAL NATIONAL TRUCK MOUNT FRAME  PROMOTES POOR ACCESS AND COOLING / BREATHING FOR  THE ENGINE  AND ITS COMPONENTS. Blue Baron's  Unique Simplistic Design V

V Always Cool Fresh Air Inducted for Maximun Long Engine Life & Performance. V V

Easy Access V E asy Access To Components

V Side rails provide added protection and for easy transport. V V

V V V V Avoid the "Cheap" Light Gauge Frames with the ("Engine on the Box") This will leave your Engine & Components Unprotected and increase the possibility of Personal Injury.  V V V V Nothing worse than struggling & fussing to remove a Smother Cover when doing routine servicing  or even checking you engine's oil level. Our Customers should never go through that much trouble. V ***Maybe the company that built this machine is  hoping you will take it in for a $90 / hour service charge.

V Smother Covers create poor ventilation and trap in Heat making it difficult for Engine,Blower & Internal Components to breath V Starvation of Air & Restriction (Chocking) of Air will limit life of your engine and surrounding components V V

V Cheap Light gauged steel typical of the " Cookie Cutter " method of manufacturing. Be sure to put a Fragile sticker on this little "Candy Coated" wonder. V V

SHOP & COMPARE OUR HEATING TECHNOLOGY BEATS THE COMPETITION

>

The  NEW Wave  of Heat Exchanger Technology Sweeping the Nation 

Competition's OLD Art Heat Exchangers Blue Baron's Multi-Stage All Stainless Heat Exchanger System Composed of  NEW ART Patent Pending Primary Heat Exchanger which uses a New technology known as Axis Point  TM This means Continuous Heat more stable with minimal fluctuations in temperature up to 240 degrees plus.  Skinney Low Linear Feet of Tubing in these OLD ART OBSOLETE Heat Exchangers (Bad for Heating Water)

This type of Heat Exchanger will run out practically before the second stroke of the wand!

Greater capacity of Water Storage which equates to Greater Linear footage of Tubing.

Professional Carpet Cleaners choose Exhaust Diversion on all their machines. NO EXHAUST DIVERTER!? What were they thinking!? No Exhaust Diverter which makes it Hard to do Flood Clean-up. We think the Customer deserves to have the choice of Heat or No Heat.Why lose Jobs if you do not have the right ingredients !  Our All Stainless Exhaust Diverters give our Customers the choice of Heat or No Heat. In this Economy you can not afford to lose out on this Multi Billion Dollar Industry not doing  Flood Water Recovery.  Insurance Companies pay BIG $$$ for these Special Services!

Pre-Heated Mix Tank which gives you a Head Start during those cold winter months. **Special Note** Our Exhaust Headers are all Heavy Gauge Stainless Steel not that Poor Quality Thin Gauge Steel most Competitors use. Back To The Top